jaefi.blogg.se - Zebra gx430t calibration

#Zebra gx430t calibration driver#
#Zebra gx430t calibration manual#
#Zebra gx430t calibration series#

(The configurations are sent when printing using the driver or printing the driver test page) If you are using a non-Zebra application/driver/label software determine the methods used to set these configurations and be aware the terminology for each setting in your environment may be different. In these examples, we will use the Zebra Designer Driver to configure the printer. The GX-Series printer can be configured by your driver, host application, or a utility.

#Zebra gx430t calibration manual#

If the problem persists a Media Sensor Profile can be sent to Tech Support for analysis. Refer to GX420t/GX430t User Guide: Manual Calibration for more information.Refer to GX420t/GX430t User Guide: Feed Button Modes for more information. Try Defaulting and verify the printer has calibrated correctly. Refer to GX420t/GX430t User Guide: Printer/Network Default for more information.If one label feeds each time-pressed, check your label format or Driver/Software for the source of the problem. Verify the labels are compatible with the media specifications. Refer to GX420d, GX420t, and GX430t Printer Specifications for more information.If set to Continuous the printer will not track Top-of-Form. Refer to ZebraDesigner Driver Printer Configuration Printing Preferences vs Printing Defaults for more information. Verify the printer is set to the correct Media Type.Refer to GX420t/GX430t User Guide: Label Dispenser Option for more information. Loading for Tear-Off. Refer to GX420t/GX430t User Guide: Loading Roll Media for more information. Check Media Loading and assure the guides are keeping the media aligned.Verify Software/Driver settings are not changing the calibrated values or printer configurations. If one label feeds each time pressed then the printer is properly calibrated. NOTE Press the FEED Button after calibrating. If the problem persists, a Media Sensor Profile can be sent to Tech Support for analysis. Refer to GX420t/GX430t User Guide: Manual Calibration for more information.Try Defaulting the printer. Refer to GX420t/GX430t User Guide: Printer/Network Default for more information.ĭefault settings are non-continuous web so you'll have to reconfigure if using black mark media.Perform Calibration. Refer to GX420t/GX430t User Guide: Feed Button Modes for more information.Use the GAP/NOTCH (Transmissive) Sensor for gap, notch, or hole media. Use the MARK Sensor for media with a black bar on the backing. Verify the correct setting is configured for the media type. Refer to ZebraDesigner Driver Printer Configuration Printing Preferences vs Printing Defaults for more information.Ribbon Loading. Refer to GX420t/GX430t User Guide: Loading Transfer Ribbon for more information.

Loading for Peel Mode. Refer to GX420t/GX430t User Guide: Label Dispenser Option for more information. Loading for Cutter. Refer to GX420t/GX430t User Guide: Cutter Option for more information. Refer to GX420t/GX430t User Guide: Loading Roll Media for more information.

CheckMedia and Ribbon (if used) Loading.

Prints labels then the red light starts to flash.

Labels stop printing in random locations.

Print position is drifting up and down on the labels.

Print is overlapping onto the next label.

Prints then skip a label or are skipping labels.

This information is useful for resolving issues such as:

#Zebra gx430t calibration series#

Your printer is now ready for use.GX Series Printer Calibration Applicable To

You will then get another label with the “out of dump” message on it.

Press the feed button once to exit dump mode.

After the printer stops feeding labels, it prints the internal printer information.

The status light will turn green and feed a few blank labels.

When the status indicator light starts flashing, release the feed button.

Hold the feed button down, and turn the printer back on whilst holding down the feed button.

Turn off the printer at the back and have media loaded.

Printer calibration is used to obtain consistent positioning of the label and the print by following the process below.